MVR FW 210 series F

You’re about to download MVR FW 210 series F

You have chosen to download our software.

Within a few seconds, you will receive an email containing a download link.

Having trouble using the software? Please contact support@deif.com. 

Best regards, 

DEIF A/S

The software is subject to copyright DEIF A/S
By following the above mentioned link and downloading the file you automatically accept DEIF A/S copyright and license agreement (EULA). The license agreement can be found on www.deif.com/software

This software applies to the following DEIF products:

You’re about to download 2.1.1.3-247

The main changes implemented since the last version are as follows:

New features

  • Parameter: Settable voltage measurement threshold.
  • HMI: Transformer module measurements added to mimic.
  • HMI: Imeas/Iset to I2> function.
  • HMI: Kazakh, Chinese and Russian language translations.
  • Communication: Energy measurement mapping to IEC61850.
  • Communication: Scaled analog inputs to IEC104.
  • Communication: Voltage and current THD to IEC61850.
  • Communication: U3/U4 frequency to IEC61850 and Modbus.
  • Communication: CTS2 to IEC61850 mapping.
  • Communication: Programmable stages to IEC61850.

Changes

  • Synchrocheck [25]: Added LL/DL/LD/DD-mode, ability to select line or bus as reference, additional signals.

Corrections

  • mA output: Corrected mA output accuracy.
  • Frequent start FSP (N>) [66]:Fixed issue where frequency start -stage was not working correctly.
  • AVR: Fixed issue where AVR scaling curve was not working correctly.
  • Communication: Fixed issues with IEC61850 Test outs (forced statuses) and events.
  • Directional overcurrent (Idir>) [67]: Fixed issue where protection blocking signal reset start signal to zero.
  • HMI: Corrected language encoding.
  • Synchrocheck: Fixed issue where synchrocheck was not working correctly with maximum settings.
  • TrafoModule: Fixed issue where Manual Set vector group was not working correctly.
  • General: Improved USW connection termination.
  • General: Improved option card detection.
  • General: Fixed issue where device discovery announcement message had incorrect serial number.
Ver. Date Description

2.1.1.3-247

10/01/2025

New features

  • Parameter: Settable voltage measurement threshold.
  • HMI: Transformer module measurements added to mimic.
  • HMI: Imeas/Iset to I2> function.
  • HMI: Kazakh, Chinese and Russian language translations.
  • Communication: Energy measurement mapping to IEC61850.
  • Communication: Scaled analog inputs to IEC104.
  • Communication: Voltage and current THD to IEC61850.
  • Communication: U3/U4 frequency to IEC61850 and Modbus.
  • Communication: CTS2 to IEC61850 mapping.
  • Communication: Programmable stages to IEC61850.

Changes

  • Synchrocheck [25]: Added LL/DL/LD/DD-mode, ability to select line or bus as reference, additional signals.

Corrections

  • mA output: Corrected mA output accuracy.
  • Frequent start FSP (N>) [66]:Fixed issue where frequency start -stage was not working correctly.
  • AVR: Fixed issue where AVR scaling curve was not working correctly.
  • Communication: Fixed issues with IEC61850 Test outs (forced statuses) and events.
  • Directional overcurrent (Idir>) [67]: Fixed issue where protection blocking signal reset start signal to zero.
  • HMI: Corrected language encoding.
  • Synchrocheck: Fixed issue where synchrocheck was not working correctly with maximum settings.
  • TrafoModule: Fixed issue where Manual Set vector group was not working correctly.
  • General: Improved USW connection termination.
  • General: Improved option card detection.
  • General: Fixed issue where device discovery announcement message had incorrect serial number.