SGC 120 MkII Firmware
You’re about to download SGC 120 MkII Firmware
You have chosen to download our software.
Within a few seconds, you will receive an email containing a download link.
Having trouble using the software? Please contact support@deif.com.
Best regards,
DEIF A/S
The software is subject to copyright DEIF A/S
By following the above mentioned link and downloading the file you automatically accept DEIF A/S copyright and license agreement (EULA). The license agreement can be found on www.deif.com/software
This software applies to the following DEIF products:
You’re about to download R16.00
The main changes implemented since the last version are as follows:
New features
- Added 0-5V sensor selection for pin 23.
- Added Custom Sensor.
- Added Activation & Delay for Custom Sensors.
- EIC: Added support for Baudouin Gas.
- EIC: Added support for Baudouin Wise10B.
- EIC: Added support for Caterpillar ADEM 6.
- EIC: Added support for Deutz EMR 5 Stage V.
- EIC: Added support for Doosan Stage V.
- EIC: Added support for Generic CPCB IV.
- EIC: Added support for Isuzu.
- EIC: Added support for Iveco Stage V.
- EIC: Added support for JCB.
- EIC: Added support for JCB 430/448 Stage V.
- EIC: Added support for Jichai JC15D Weifu.
- EIC: Added support for Jichai JC15T JG.
- EIC: Added support for Jichai JC190.
- EIC: Added support for Jichai WYS.
- EIC: Added support for Jing guan.
- EIC: Added support for John Deere.
- EIC: Added support for John Deere Stage V.
- EIC: Added support for Kohler.
- EIC: Added support for MAN.
- EIC: Added support for MAN EMC Step 2.0.
- EIC: Added support for MAN EMC Step 2.5.
- EIC: Added support for Perkins CPCB IV.
- EIC: Added support for Perkins Stage V 120xJ.
- EIC: Added support for PSI.
- EIC: Added support for Scania EMS2 S6.
- EIC: Added support for Weichai Diesel.
- EIC: Added support for Weichai e6gas.
- EIC: Added support for Weichai Gas.
- EIC: Added support for Weichai Wise10B.
- EIC: Added support for Weichai Wise15.
- EIC: Added support for Yuchai.
- EIC: Added support for Generic CPCB4 +.
- Added Auto Load Transfer In Manual for Mains as a separate parameter.
- New Data added over Modbus.
Changes
- Interlock of breaker feedback added as an interlock for Contactor latching of Generator and Mains.
- The breaker on the display now mimics the contractor feedback.
- Limited Counter Reset removed. The user can now reset any change multiple times with a password.
| Ver. | Date | Description |
|---|---|---|
|
R16.00 |
15/10/2024 |
New features
Changes
|
|
R15.00 |
24/04/2024 |
New feature• New engine protocol added: |
|
R14.01 |
11/12/2023 |
SGC 120 Mk ll offline firmware initial release. R12.00 was the initial release for the SGC Mk ll variants. All previous releases were over smart flash. New feature:• Config and M-Logic flashing in live mode.
Changes:• Updated start sequence to avoid breaker closure before safety monitoring expires. |
On this page, you can download software updates for your product(s) and help yourself to various utility tools and add-ons that will assist you in setting up, detecting faults and configuring your product(s).
Please be advised that not all of our products can be updated by the user. Nor do all of our products come with a utility tool. Consequently, the list on this page cannot be considered an overview of our product programme.
DEIF will register your download along with the used e-mail address for the purpose of sending out information on future updates, if requested.
DEIF cannot be made responsible for any consequences of failed product updates or use of utility tools. Nor can DEIF A/S be made responsible for consequences of changes in behaviour of products due to a software upgrade. It is always the responsibility of the user to ensure correct set-up and configuration before commissioning. Please study the version log of the software before updating the product.
Licence agreement for software downloaded from www.deif.com
Downloaded software remains the property of DEIF. The software may not be distributed for commercial purposes, changed or reused in full or in part or sold to any third parties.
The latest versions for full functionality
As always, we recommend that you install our offered improvements to fully utilise your DEIF product.
All improved software can be downloaded at your convenience at www.deif.com under “Software”.
Should you have any questions or experience problems finding the relevant software for your product, please feel free to call DEIF A/S at +45 96149614 or your relevant local DEIF office. Alternatively, we are always ready to assist you, if you send an e-mail to support@deif.com.