Full gas engine control

The insulation monitor AAL-2 - the features

The insulation monitor, AAL-2, from DEIF has a high number of features:

• Insulation monitoring of AC networks of up to 440 V AC
• 10 M or 1 M ranges
• Adjustable warning set point
• Delay to prevent unwanted warnings

• Maximising PV penetration
• Spinning reserve demand
• Minimum genset load requirement
• Suitable for self-consumption and IPP applications
• Support of SunSpec and other relevant protocols
• Monitoring and supervision
• Meteorological measurements
• Fully integratable in AGC Power Management applications
• Simple graphical configuration
• Record time commissioning with DEIF Emulation – uses and verifies the functions of the real system for test, production and design
• Suitable for power management solutions fitted with AGC PM genset controllers
• Suitable for stand-alone solutions using multi-instruments such as DEIF’s MIB or MIC

• 8 relay outputs
• 240 V AC or 30 V DC relay contacts
• 8 A relay rating
• CAN bus interface
• LED indication of status and input state
• 12/24 V DC supply

Data Acquisition Unit

• Event-based logging
• Updates Over-the-air (OTA)
• 3G UMTS/HSPA+
• 2G Edge/GSM/GPRS
• 1 communication LED, 1 signal LED
• GNSS (GPS/Galileo/Glonass)
• Ultra low power mode
• Ethernet (RJ-45) for Modbus TCP/IP

Simple to install

• 3-way DIN rail clip orientation
• Fast IP configuration via micro USB
• Antennas and cables included
• High vibration mounting

• Control of electronic speed governors
• Setting of integrating time (like variable gearboxes)
• Adjustment of output signal
• Offset adjustment
• Manual/auto mode
• Analogue and digital output
• Converts a J1939 CAN input to an analogue or a PWM output
• Q96 panel mounting

• Accuracy class: 1.5
• 90 ° pointer deflection
• IP52 (IP54 on request)
• Customised and exchangeable scale available for 90 °
• Measuring range: 40 to 800 V (Q48: 40 to 300 V), 1 to 60 A (Q48: 1 to 40 A)

• Automatic.
• Voltage regulation
• Breaker-time compensation.
• Synchronisation of generator to busbar
• Circuit breaker time compensation
• Voltage control
• LED indication of status
• LED for activated control
• LED for synchronising signal
• 35 mm DIN rail or base mounting

• Mains/Generator/Motor protection
• The unique M-Logic, a simple configuration tool
• Engine protection with backup on shutdown channels
• Governor and AVR control
• J1939 engine com/mirrored Modbus/Profibus/TCP/IP
• Multible display units and operator panels possible
• Additional Operator Panel (AOP)

• Generator/busbar protection
• Synchronisation
• Multiple display units and operator panels possible
• Engine control and communication

• Visualised solution overview via customisable dashboard 
• World map overview and GPS tracking
• Alarm notifications (email)
• Reports (PDF, CSV)
• Fleet management (unit grouping & scheduling)
• Flexible user/team management and user permissions
• Two factor verification for enhanced security
• Templates for selected DEIF products

Dashboards widgets

• Direct value visualisation
• Multiple options of guages
• World map overview 
• Group data in lists
• Show latest notifications
• Trending with graphs 

Responsive web service

• Designed for portable devices
• Works with most popular browsers
• Requires Insight subscription plan​

• Primary current: 1 or 5 A
• Secondary current: 5 or 1 A
• Accuracy class/protection class: 0.5 or 1.0

• Short response time (70 ms)
• 3-phase current detection on both generator sides
• Active adjustment of non-balanced current measurements
• Measuring accuracy 1 %
• Display indicator for all measurements
• DIN rail or base mounting with remote mountable display

• Accuracy class: 1.5
• 90 ° and 240 ° pointer deflection
• Available in size Q96

• Short circuit relay (I>>)
• ANSI code 50 and 51
• Measurement of 3-phase currents
• LED indication of fault condition
• Timer-controlled tripping
• LED indication for activated relay
• 35 mm DIN rail or base mountin

• Earth fault protection at two levels
• Built-in filter for 3rd harmonic
• LED indication of fault condition
• Timer-controlled tripping
• LED indication for activated relay
• 35 mm DIN rail or base mountin

• Generator and prime mover protection
• ANSI code 32
• 3-phase measurement
• LED indication of alarm condition
• Timer-controlled tripping
• LED indication for activated relay
• 35 mm DIN rail or base mounting

• Generator and prime mover protection
• ANSI code 32
• 3-phase measurement
• LED indication of alarm condition
• Timer-controlled tripping
• LED indication for activated relay
• 35 mm DIN rail or base mountin

• Factory-configured transducer for voltage, current, frequency or phase angle measurement
• Aux supply: from 57 to 690 V AC
• Aux supply: 24 to 220 V DC
• Class 0.5 measurement
• Supply and measuring voltage up to 690 V
• Pre-configuration or easy PC tool configuration
• Configurable up to three output slopes

• Prioritised load groups
• Anticipated load-dependent start
• Integrated in power management system
• Automatic startup of extra gensets
• Avoid overload of system
• Manual or automatic control of feeders
• Easy setup via USW and intuitive to use
• Easy commissioning, prepare SW setup before commissioning, live status of feeders shown in USW
• Flexible setup of different application types
• CANbus communication, long distance communication (up to 300 m)
• Security of supply – safety based on feeder priority

• Vector shift
• Detection of vector shift
• ANSI code 78
• Mains disconnection on mains failure
• Ensures no asynchronous reconnection
• LED indication of fault condition 
• LED indication for activated relay
• 35 mm DIN rail or base mounting

• Frequency and power control. With start/stop 
• Built-in power and frequency transducer
• Constant power or isochronous mode
• LED indication of status
• LED indication for activated control
• 35 mm DIN rail or base mountin

• Programmable logic
• Fast and easy commissioning and service with front communication port and intuitive software
• Password-protected user levels
• Individual voltage and current harmonics up to 31st
• Redundant Ethernet with Modbus TCP
• RS-485 Modbus RTU communication
• IEC 60870-5-104/103/101 communication
• IEC 61850 communication (incl. HSR, PRT, PTP acc. IEEE 1588) and GOOSE
• On-site replaceable spare part modules
• Class 0.5 power and energy measurement (Class 0.2S optional)
• Conformal Coating available for all devices
• Marine type approval by major class societies

AGC 150 BTB - features

• Automatic close of bus tie breaker if the system requests help 
• Manual control of bus tie breaker
• Section management
  
  
• 12 Digital inputs and 12 digital outputs
• Communications ports (CAN, USB, RS485, Ethernet).
• Event & alarm log (500 each)
• Programmable PLC editor

• Fully scalable multi-master system of up to 992 gensets
• Simple graphical configuration
• Easy control from one central point of intelligence
• Cost-optimised design
• Reduced fuel consumption
• Grid support
• Monitoring and supervision
• Emulation Solution – uses and verifies the functions of the real system for test, production and design
• Suitable for hybrid power solutions fitted with ASC PM controllers

• 16 digital inputs
• Positive or negative common for 2x8 inputs
• CAN bus interface
• LED indication of status and input state
• 12/24 V DC supply

• Up to 1,000 V L-L AC voltage input
• Up to 20 A AC current input
• Accuracy class: 0.5
• Password protection
• Trip time typically below 50 ms
• Two-stage trip setting
• Start-up delay
• 13 different protection functions
• RS-485 serial Modbus communication
• Fast and simple commissioning and setup from M-set
• Universal power supply of 20 to 300 V DC/48 to 276 V AC
• Marine approval by GL/DNV

• Dimensions to DIN 43703
• Class 0.5
• Extensive programme
• Standard versions in stock

• Standard pointers, diagonal. 45 to 65 Hz, 150 to 600 V AC. 
• Robust and thoroughly tested construction
• Available in Q96 DIN size design
• High accuracy and linear read-out
• High immunity to 3rd harmonics

• Unique CANbus integration between DVC 550 and AGC genset controller
• Start management capability with start on threshold, soft start and close before excitation (run-up sync) 
• Intelligent drying and ventilation mode for generators 
• Short circuit limitation
• Loss of voltage sensing alarm
• Over/under excitation limitation 
• Optimises genset performance and size using engine help functions
  • Load acceptance module (LAM) assists the generator during heavy loads
  • Negative forcing to avoid voltage peak during load sheddin
  • U/F ramp
  • Soft voltage recovery
  • Stator current limitation
• Settings from AGC genset controller shared with the DVC 550 via CANbus
• Grid code compliant VDE410 and VDE4105

• Plug and play
• Build in AOP (additional operators panel) customizable buttons and status lamps
• Quick instrument selection directly from the screen
• Tier 4 Final support with automatic jump to dedicated Tier4 page
• Visual capability curve with actual working point of the genset
• Easy search functionality in several menus
• Live application supervision
• Possibility to merge alarm and event logs
• Service menu with estimated date for next service
• Live I/O overview

• Wide screen format
• True glass front
• Capacitive touch screen
• Multi-touch and Gestures
• Robust aluminium housing
• SD card slot for easy storage and updating
• USB hosts for printers, accessories, data storage and updating
• Dimmable LED backlight
• Web server for remote access from i.e. mobile devices
• 3 Ethernet ports with integrated switch
• Serial communication (RS-232, RS-422 and RS-485)
• Wide range of support for industrial protocols
• OPC UA Server and Client
• JAVA scripting
• CODESYS V3 (optional)
• Powerful ARM Cortex-A9 processor
• Plug-in module for CANbus (CANopen/J1939)
• Wide operating temperature -20°C to +60°C
• Marine certifications
• Certified for hazardous environments
• Available in 7", 10", 15" and 21" sizes

AGC 150 Mains - features

Operating modes with single or multiple mains: 

AMF, Fixed power, Mains power export Load take over, Peak shaving

• Mains (Utility)  
• power monitoring (kW, kV, A & pf)
• decoupling protection
• kW export protection
• electrical protections

• No break transfer of load 
• Multi start settings
• Minimum of starting genset
• 12 Digital inputs and 12 digital outputs
• Communications ports (CAN, USB, RS485, Ethernet).
• Event & Alarm log (500 each)
• Programmable PLC editor

• 8 multi-functional inputs
• Wire break detection
• CAN bus interface
• LED indication of status and input state
• 12/24 V DC supply

• Short circuit and over-current circuit relay (I> + I>>)
• ANSI code 50 and 51
• Measurement of 3-phase currents
• LED indication of fault condition
• Timer-controlled tripping
• LED indication for activated relay
• 35 mm DIN rail or base mounting